Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - ricklap77

Pages: [1] 2 3
1
The Tech Barn / How to tell year of a Teo Pro Car???
« on: July 22, 2016, 09:14:39 AM »
Where is the ID plate with date of manufacture on a Teo Pro Car???

2
Racing Discussion / How to tell year of a Teo Pro Car???
« on: July 22, 2016, 09:13:56 AM »
Where is the ID plate with date of manufacture on a Teo Pro Car???

3
The Tech Barn / Re: BRP set up blocks???
« on: March 18, 2016, 02:47:22 PM »
Thanks a lot!  I didn't know they gave the measurements in the catalog!

4
The Tech Barn / BRP set up blocks???
« on: March 18, 2016, 06:59:04 AM »
I would like to make my own set up blocks with wood for squaring my car and need to know the length of those set blocks that Bicknell sells.  Thank you!

5
The Tech Barn / Bicknell set up blocks heights???
« on: March 18, 2016, 06:57:39 AM »
I would like to make my own set up blocks with wood for squaring my car and need to know the length of those set blocks that Bicknell sells.  Thank you!

6
Racing Discussion / Re: PMC race cars
« on: December 14, 2015, 06:40:15 PM »
Thanks Casper60!  Anyone else can confirm that?  I know a lot of guys are or were racing with those cars.

7
The Tech Barn / PMC race cars
« on: December 13, 2015, 01:13:01 PM »
Just wondering if the pmc chassis can take all Bicknell parts on such as panhard, body mounts, side rails, etc... just like Hig Fab chassis can?

8
Racing Discussion / PMC race cars
« on: December 13, 2015, 01:12:16 PM »
Just wondering if the pmc chassis can take all Bicknell parts on such as panhard, body mounts, side rails, etc... just like Hig Fab chassis can?

9
The Tech Barn / Squaring rear suspension dirt sportsman modified
« on: June 15, 2015, 05:11:17 PM »
My rear end is 1/8 of an inch back on the right.  Would that just be good on short tracks like quarter mile tracks?  I was told I would need less stagger this way.  I am thinking about setting the rear end square on longer tracks.

10
The Tech Barn / Clicking noise from the steering box?
« on: May 12, 2015, 11:58:03 AM »
I hear a clicking noise from my profile steering box when I turn.  It`s not really old.  What could it be.  It works fine.

11
Racing Discussion / Re: 2015 dirt rule cage upper bars
« on: February 10, 2015, 11:47:31 AM »
Excuse me but you said not going to be mandatory anywhere but the mile, you mean all dirt tracks under Dirt car?

12
Thanks for the info 2cars2much!  When I receive the parts I ordered, I'll try it without the recirculating catch can because I have no room to put it to the highest point.  I'll also use a non recovery cap so air doesn't get sucked in when the system cools down.

13
I just bought an intake filler from moroso with an extended 45 degree filler neck that is about 6 inches high.  I will run from the back of it (1/4 npt) a hose that goes to the 1/4 npt on the top corner of my radiator.  My recirculating catch can is located in front of the rad and connected to the top of of the filler neck.

14
I am thinking about getting a moroso intake filler with a 45 degree extended filler neck and getting rid of my lower inline filler.  Plus I'll run a hose from the intake filler to the rad.  I guess that way I play safe.  What do you guys think?

15
The inline filler is right by the radiator and there`s a tube going to the bottom of my recirculating catch can with a tube on top (for air) of my recirculating catch can.  The inline filler is at the same height as the top of the rad which is higher then the intake.  I have no thermostat.  I have only been reving it in the garage and could not get the heat higher than 140.  I am wondering if when the heat goes up the air will be purged into the recirculating catch can and then escape?

Pages: [1] 2 3