Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - sharpd12

Pages: [1] 2 3
1
Classified Ads / Re: Street/hobby stock roller
« on: November 15, 2020, 12:58:24 PM »
SOLD

2
Classified Ads / Street/hobby stock roller
« on: October 18, 2020, 02:53:50 PM »
Have a nice Camaro pure/hobby/street stock. No jacking bolts. 2x3 chassis after front clip. Can run heim front shocks or stock location. Will only cone with a steel Camaro roof and the decking as far as the body goes, has new leaf spring sliders in the back but can be put back to shackles if need be. Leaf springs only have a handful of nights on them and weights off them 99% of the time it wasn’t on the track. Was gonna keep it and run as a hobby but don’t even have time to run my street stock lately. Will come with couple sets of headers, any extra suspension parts I have for it. 9” rear, no gear unless you have a set to give me on trade with it. Has all brake and fuel lines and fuel cell. Will be a roller if bought at asking price other wise you will need to supply wheels to transport it home(4.75) message me for details or any questions. Open to some trades just ask me and I’ll let you know.

Everything that I have in it goes. Extra leafs. Shocks. Control arms. Headers. Exhaust pipes for the chassis. Extra rearend housing.
Livonia NY 14487
Call or text 3153233174
Can text pics
900 obo need gone before snow falls

DO NOT WASTE MY TIME PLEASE!

3
Classified Ads / ISO Chrysler leafs
« on: January 05, 2020, 07:49:53 PM »
Looking for a set of Chrysler leaf springs. Used is fine. Looking for something someone may be tossing out. I am swapping from chevy springs and looking for a set of Chrysler’s just for mock up.
I’m in Livonia but I’m in Rochester throughout the week. Anywhere local to me I can pick up whenever.
Call or text 315-323-3174
Thanks,
Dakota

4
The Tech Barn / Re: Corner misfire
« on: August 29, 2019, 08:16:35 PM »
I was just going over everything again. I feel that my timing chain may have too much play? I can Rock the crank between 3-4 degrees according to timing tab before my distributor starts to move.

Car starts to act up as soon as a let off for corner entry and attempt to get back on throttle.

5
The Tech Barn / Re: Corner misfire
« on: August 25, 2019, 06:24:04 PM »
I have been chasing it still for weeks. I have changed carbs and yes floats were adjusted properly on Both. I changed battery to be safe I had plenty of juice. Tried jetting up and down. No difference. I changed back to my old distributor to make sure that was not the problem. Fuel pressure was at 8psi When tested at home. Not sure of on trAck pressure.

I will be pulling fuel pump and fuel push rod tonight to make sure rod is not worn down.

6
The Tech Barn / Re: Corner misfire
« on: July 25, 2019, 08:35:20 AM »
Does this happen if your fuel cell/tank is full, or when it's near empty? If it happens as the tank gets to a lower level, is your "fuel pickup" offset so it's at the right side of your fuel cell/tank? If not, centrifugal force is pushing the gas away from your pickup, as you're cornering, momentarily starving the engine for fuel.

Had the cell filled to the top and I did check pick up to make sure it’s in the right corner.

7
The Tech Barn / Corner misfire
« on: July 25, 2019, 06:45:45 AM »
Having a problem with my street stock. Going into corner and car just starts to stumble and fall on face until back going straight. Doesn’t make difference if I feather throttle,hold to floor, or even throw it in and try coasting through as mush if the turn that I can. I adjusted float so there just a trickle with a little rocking of the car. Any ideas or help would be great!
Thank you in advance

8
The Tech Barn / Vortec heads cut for more valve lift.
« on: November 05, 2018, 09:03:59 PM »
Who in Rochester NY can take my stock vortec heads and cut the seats and guides so I can run a bigger cam. Also looking to have set up for screw in studs with guide plates.

9
Racing Discussion / Boy Dying From Cancer Needs Racing Stickers
« on: August 19, 2018, 10:18:49 PM »
http://hudsonvalleycountry.com/boy-dying-from-cancer-needs-racing-stickers/

Let’s try to help this poor little guy out! Check out the article if you haven’t read about him yet, search it online. Let’s give this boy what he wants before he’s gone.

10
If I only had the Facebook I would.

11
To run my street stock would I need to run both days or could I come just Saturday?

12
The Tech Barn / Re: Rearend width help please!!
« on: November 30, 2017, 12:15:25 PM »
That could always be an option.. but really wondering how wide of rears guys are running in there leaf spring cars

13
The Tech Barn / Rearend width help please!!
« on: November 29, 2017, 08:57:12 PM »
Looking into getting a floater rearend for my Camaro Street stock. I run chevy springs in it. Wondering on what width I should go with when ordering/looking

14
Racing Discussion / Re: Traditional street stocks?
« on: October 03, 2017, 08:32:03 PM »
Sounds to me like nothing will change. IMO

15
Racing Discussion / Re: Traditional street stocks?
« on: September 28, 2017, 07:16:36 PM »
Yeah.. I sure am interested to know what was said.

Pages: [1] 2 3